![]() Ensure they connect properly for accurate readings. Place the red and black probes on the fuse terminals. This will help you know whether the multimeter is working properly. Write down any readings projected on the screen. After that, place the probes against each other and see if the multimeter will display any reading. You can get a multimeter from a friend or buy one from an online or local auto spare part shop. If none or only one of them illuminates light, it means the fuse is blown. The tester should illuminate as you place it on both fuse terminals. Now, touch the screw end of the tester on both fuse ports. If the tester bulb glows, you have a good connection. To check a 60 amp fuse with a test light, connect the wire to the negative battery cable and touch the other end on the positive battery cable. Using a test lightĮvery electrician should have a test light. ![]() However, if you’re not convinced with the result, proceed to the next method. If the metal strip is broken or you notice a powder or burnt-like substance, you likely have a blown fuse. If you suspect your 60 amperage fuse is blown, remove the fuse cover and inspect the port. ![]() But you can also run a visual inspection on cartridges-like fuses – 40, 50, 60, and 75 amps. Visual inspection is mainly for blade-like fuses – 25, 20, 15, 10, 7.5, and 5. Let’s start by explaining how to tell if a square fuse is blown using a visual inspection. The best way to tell if a car fuse is blown is to test it with a multimeter, volt meter, test light, or by visual inspection. Therefore, it is necessary to test the fuse before replacing it. While fuses blow and prevent electric flow from passing to the vital component whenever there is a power surge, it doesn’t necessarily mean the fuse is blown when an electrical or electronic component is not working. So it’s essential to check the drawing on the fuses or your owner’s manual to know what component uses 60 amp fuse in your vehicle. This means a Toyota Camry can use a 40 amp fuse for the high beam lights while a Chevy Silverado uses a 60 amp for the same high beam headlight. It’ll be unfair if I fail to mention that different cars use different electrical systems and, therefore, different fuses. The high beams require higher fuse amperage, like 60 amps, to protect them against power surges since they use more electric flow than the low beams. High beam headlightsĬar high and low-beam headlights run on different circuits. So, automakers safeguard them with a 60 amp fuse against a power surge. It, however, requires high electric flow to carry out this function. It compresses the ac gas before exporting it to other ac system components. The ac compressor is the heart of the air conditioning system. Because of this, most car manufacturers protect them against power surges with a 60 amps fuse. Power seats need high voltage to work smoothly. Most auto manufacturers protect the power windows with a 60 amp fuse to prevent any damage when there’s a power surge in the vehicle. ![]() Alternator circuitĪ 60 amp fuse protects the alternator circuit, ensuring the vehicle runs with the appropriate electric voltage. The starter motor is a crucial ignition system component that turns the engine when the driver turns the ignition key. Typically, a 60 amp fuses protect the starter circuit, which protects the starter motor. Here are what 60 amp fuses protect in cars Starter circuit The fuse box cover has a diagram that indicates what each fuse protects. The fuse box contains several fuses that control different electrical circuits. These fuses are rated for circuits with no higher than 32 volts.Ħ0 amp fuses are typically located in fuse boxes in the cabin or under the hood. Here, we’ll answer the question, what does a blown 60 amp fuse look like? At the end of this article, you’ll be able to tell when a 60-amperage fuse is burnt by just looking at it.Īs explained earlier, car fuses are a set of fuses used to protect electronic and electrical components from power surges. A fuse is typically a two terminal with a small metal strip across them-the metal strip cuts whenever there’s a power surge, preventing the key component from damaging.Ĭars have several electrical and electronic appliances and various fuses to protect these components from damage when there is a power surge. In cars, fuses act as a safety feature that protects electronics from blowing up due to a power surge in the system. ![]()
0 Comments
Leave a Reply. |